FUCHS RENOLIN PG1000价格RENOLIN PG 100, 150, 220, 320, 460, 680, 1000 Fully synthetic polyglycol based gear- ａnd general lubrication oils PM 4-01/02 Previous editions are invalid ａnd should be destroyed. PI 4-1042e Page 1 Description The importance of gear- ａnd general lubrication oils based on polyglycols is still growing. The initial raw materials for producing polyglycol are petroleum ａnd natural gas. Polymers of different chain lengths are produced by the thermal decomposition ａnd subsequent synthesis of the raw materials. Different viscosity grades can be produced by just changing the chain length of the molecule. The polyglycols obtained using this synthesis have a uniform structure. An optimum adjustment of RENOLIN PG is obtained by specially selected additive combinations. The special properties of the RENOLIN PG oils are: • very good viscosity-temperature behavior • very good shear stability, shear losses < 1 % acc. to DIN 51 382 • high pressure absorption capacity • high wear protection • very low friction coefficient; because of this reduction in operating temperature is possible • very good oxidation stability, high aging resistance • excellent corrosion protection of steel ａnd non-ferrous metals • low foaming characteristics • high flash point Applications RENOLIN PG transmission oils are suitable for highly-stressed spur gear, planetary gear ａnd worm gear drives. Applications when enhanced gliding performance is requested, transmission oils on polyglycol basis have advantages compared to mineral oils. Advantage: Decrease in the oil temperature ａnd the possibility to extended oil change intervals. RENOLIN PG oils can be used at continuous operating temperatures up to 180°C ａnd in some cases even higher. Products of the RENOLIN PG series are also used as lubricating oil for compressor handling, process gases like methane, ethane, butane. RENOLIN PG-oils are not compatible with mineral oils! Approvals RENOLIN PG is recommended by the Flender company for lubrication of spur gears, bevel gears ａnd planetary gears. RENOLIN PG 100, 150, 220, 320, 460, 680, 1000 Fully synthetic polyglycol based gear- ａnd general lubrication oils PM 4-01/02 Previous editions are invalid ａnd should be destroyed. PI 4-1042e Page 2 Typical Properties R E N O L I N Properties Unit PG 100 PG 150 PG 220 Test method Colour - 0,5 0,5 0,5 DIN ISO 2049 Density at 15°C kg/m³ 997 1000 1002 DIN 51 757 Flashpoint °C 269 258 278 DIN ISO 2592 Kinematic Viscosity at 40°C mm²/s 100 150 220 DIN 51 562 at 100°C mm²/s 17,2 24,9 35 Viscosity Index - 189 200 208 DIN ISO 2909 Pour point °C -48 -45 -45 DIN ISO 3016 Neutralization number mgKOH/g 0,6 0,6 0,6 DIN 51 558 Foaming Sequ. I to III 24°C immediately/after 10 min ml 10/0 20/0 10/0 ASTM D 892 93.5°C immediately/after 10 min ml 10/0 10/0 10/0 ASTM D 892 24°C nach 93,5°C immediately/after10 min ml 10/0 10/0 10/0 ASTM D 892 Copper corrosion degree of Corr. 1 - 100 A 3 DIN EN ISO 2160 FZG mechanical gear test rig failure load FZG A/8,3/90 stage > 12 > 12 > 12 DIN 51 354-2 FZG micro pitting test GT-C/8,3/90 step-loading test load- G F T h o c h * FVA-Infoblatt stage Nr. 54/I-IV Continuous load test load stage G F T h o c h * Steel corrosion degree of (Corrosion protection) corr. 0-A 0-A 0-A DIN 51 355 * Gray discoloration test high RENOLIN PG 100, 150, 220, 320, 460, 680, 1000 Fully synthetic polyglycol based gear- ａnd general lubrication oils PM 4-01/02 Previous editions are invalid ａnd should be destroyed. PI 4-1042e Page 3 Typical Properties R E N O L I N Properties Unit PG 320 PG 460 PG 680 PG 1000 Test method Colour - 0,5 0,5 0,5 0,5 DIN ISO 2049 Density at 15°C kg/m³ 1050 1053 1053 1054 DIN 51 757 Flashpoint °C 234 267 264 292 DIN ISO 2592 Kinematic Viscosity at 40°C mm²/s 320 460 680 1000 DIN 51 562 at 100°C mm²/s 56,2 77,4 115,2 174 DIN 51 562 Viscosity Index - 244 251 270 287 DIN ISO 2909 Pour point °C -45 -42 -42 -39 DIN ISO 3016 Neutralization numberl mgKOH/g 0,6 0,6 0,6 0,6 DIN 51 558 Foaming Sequ. I to III 24°C immediately/ after 10 min ml 20/0 10/0 20/0 10/0 ASTM D 892 93,5°C immediately/ after 10 min ml 5/0 20/0 10/0 10/0 ASTM D 892 24°C after 93,5°C immediately/ after 10 min ml 20/0 10/0 20/0 20/0 ASTM D 892 Copper corrosion degree of Corr. 1 - 100 A 3 DIN EN ISO 2160 FZG mechanical failure gear test rig load FZG A/8,3/90 stage > 12 > 12 > 12 > 12 DIN 51 354-2 FZG micro pitting test GT-C/8,3/90 step-loading test load stage G F T h o c h * FVA-Infoblatt Continuous load test load stage ..............G F T h o c h * Nr. 54/I-IV Steel corrosion degree of (Corrosion protection) corr. 0-A 0-A 1-A 0-A DIN 51 355