产品基本信息：
型号：oil 4 UH1-100 N
英文名称:Kluberoil 4 UH1-100 N
粘度等级：ISO VG 100
品牌/产地：克鲁勃，德国
包装规格及价格：20L/3580      200L/33000
类型：食品级润滑油

宝贝描述：
说明：Klüberoil 4 UH1-32...1500 N是用于食品加工润滑剂和制药业。他们满足的要求德国法律管辖食品和相关辅助设备（LMBG，秒5，第1句，1）和美国提出的要求证券交易委员会21 CFR“准则FDA的规定“和178.3570是符合要求NSF H1注册。Klüberoil4 UH1-68...1500 N油符合中电的要求。当测试在FZG齿轮试验台根据根据DIN51354，第2部分，A /8,3/90，油呈划伤负载> 12和具体损失重量<0.2毫克/千瓦时。特别是制定了在使用食品加工和制药产业，这些润滑油展良好的抗磨损和极压性能以及优秀lowtemperature特征。腐蚀防护性能这些油都是很好的作为是他们的老化和氧化稳定性。他们因此，有一个高抗剪切并没有泡沫。

应用：Klüberoil4 UH1用于润滑的摩擦点在食品加工和制药机械。它们尤其适合为鞭策，斜面和润滑蜗杆齿轮，轴承，主轴和关节，以及电梯，驱动器和在低温下输送链。

包装规格：20升罐200升鼓

英文：
Klüberoil 4 UH 1-32 N … 1500 N oils
Synthetic lubricating oils for the food-processingand pharmaceutical industries
Description
Klüberoil 4 UH 1-32 N…1500 N oils
are lubricants for the food processing
and pharmaceutical industry.
They meet the requirements of the
German law governing food products
and associated ancillaries
(LMBG, sec. 5, para 1, sentence 1)
and the US requirements set forth in
the "Guidelines of sec. 21 CFR
178.3570 of FDA regulations" and
are in line with the requirements of
NSF H1 registration.
Klüberoil 4 UH 1-68…1500 N oils
meet the CLP requirements. When
tested on the FZG gear test rig according
to DIN 51 354, part 2,
A/8,3/90, the oils showed a scuffing
load of > 12 ａnd a specific loss of
weight of < 0.2 mg/kWh.
Especially formulated for use in the
food-processing ａnd pharmaceutical
industries, these lubricating oils exhibit
good antiwear ａnd EP properties
as well as excellent lowtemperature
characteristics.
The corrosion protection properties
of these oils are very good as is their
ageing ａnd oxidation stability. They
also have a high resistance to shear
and do not foam.
Application
Klüberoil 4 UH 1 oils are used for the
lubrication of friction points in foodprocessing
and pharmaceutical machinery.
They are especially suitable
for the lubrication of spur, bevel and
worm gears, bearings, spindles and
joints, as well as of lift, drive and
conveyor chains at low temperatures.
Application notes
When used in gears, Klüberoil 4 UH
1 oils may be applied by immersion,
immersion circulation or injection.
Drip-feed lubrication (e.g. for chains)
and application by brush or oil can is
also possible.Klüberoil 4 UH 1 oils are miscible
with mineral oils ａnd polyalfaolefin
oils. However, we recommend
cleaning the oil circulation system or
flushing it with the new oil prior to
using Klüberoil 4 UH 1 for the first
time. Especially with a view to the
H1 requirements in the foodprocessing
industry, any mixing of
Klüberoil 4 UH 1 oils with non-foodgrade
lubricants should be avoided.
For permanent temperatures at the
seal edge up to 100 °C, NBR seals
(acrylonitrile-butadiene rubber) may
be used. For higher temperatures, it
is safer to use FKM seals (fluorinated
rubber) instead. It should be
noted that elastomers from one or
several manufacturers can behave
differently. Therefore the data given
in the "compatibility with elastomers"
table should be used for reference
purposes only. A compatibility test
should always be carried out with
the elastomers which are actually
used.
Viscosity selection for rolling bearings
and gears
To ｓelect the correct oil viscosity,
observe the bearing manufacturer＇s
instructions or refer to worksheet 3
from the Society of Tribology (GfT).
For determining the correct viscosity
for gears, the manufacturer＇s instructions
take priority.
Only in cases where there are no
gear manufacturer＇s instructions, the
viscosity can be selected in accordance
with the enclosed worksheet
"Klüberoil 4 UH 1 oils – selection of
oil viscosity for gears".
Service temperature range*:
ISO VG 32 to 100
approx. - 35 °C to approx. 120 °C
ISO VG 150 to 460
approx. - 30 °C to approx. 120 °C
ISO VG 680 to 1500
approx. - 25 °C to approx. 120 °C
When used for loss lubrication, the
lubricant may be exposed to higher
temperatures, depending on the
relubrication intervals. We will be
pleased to provide samples for testing.
* Service temperature range:
Service temperatures are guide values which depend
on the lubricant＇s composition, the intended
use ａnd the application method. Lubricants change
their consistency, viscosity or apparent dynamic
viscosity depending on the mechano-dynamical
loads, time, pressure ａnd temperature. These
changes in product characteristics may affect the
function of a component.

Minimum shelf life
The minimum shelf life is approx. 24
months if the product is stored in the
original closed container in a dry
place.

Pack sizes
400 ml spray can (ISO VG 1500)
5 l canister
20 l canister
200 l drum