【友情提示】：本产品仅供科研研究使用，不得用于人体临床直接检测。避免给您带来不必要的损失，请仔细阅读购买说明！

本试剂盒仅供研究使用，齐一生物销售：021－6034 8496；181214 53965；173021 04490欢迎选购！

操作步骤

1.准备试剂，样品和标准品

2.加入准备好的样品和标准品，37℃反应30分钟

3.洗板5次，加入酶标试剂，37℃反应30分钟

4.洗板5次，加入显色液A、B，37℃显色15分钟

5.加入终止液

6.15分钟之内读OD值

7.计算
齐一生物供应ELISA试剂盒检测的目的是为实验提供准确可靠的定量分析实验依据。为了保证实验数据的可靠性，在实验过程中必须坚持全面质量控制和全过程质量控制。在收集标本前都必须有一个完整的计划。

【小鼠6酮前列腺素F1a(6-keto-PGF1a)ELISA试剂盒】样本保存条件：

1.2-8℃冰箱*多放2周

2.-20到-50℃的冰箱可以放3-6个月

3.-50℃以下的冰箱，可以放一年

【小鼠6酮前列腺素F1a(6-keto-PGF1a)ELISA试剂盒】样本收集

1.血清样本用干燥管（红色）或者促凝管（黄色）收集

2.血浆用抗凝管，一般有EDTA抗凝（紫色）、枸橼酸钠抗凝（黑色或者蓝色）

3.动物组织匀浆（细胞）：

              1g组织加入9ml PBS（浓度为0.1M，pH为7.4的）测分泌型指标

              1g组织加入1ml组织裂解液加入8ml PBS 测细胞内

粪便样本：1g样本+9ml PBS（浓度为0.01M，pH为7.4的）

没有PBS的话也可以用一下生理盐水，还是用PBS

【小鼠6酮前列腺素F1a(6-keto-PGF1a)ELISA试剂盒】样本离心转速及时间

1.试管采集的样本：3000转，离心五分钟取上清

2.离心管或者EP管采集的样本：5000－－8000转3分钟取上清

3..样本保存－－如果样品不立即使用，应将其分成小部分-70 ℃保存，避免反复冷冻。尽可能的不要使用溶血或高血脂血。如果血清中大量颗粒，检测前先离心或过滤。不要在37℃或更高的温度加热解冻。应在室温下解冻并确保样品均匀地充分解冻。

【小鼠6酮前列腺素F1a(6-keto-PGF1a)ELISA试剂盒】以上样本采集及处理方式供您参考，如有问题请来电，齐一生物销售：021－6034 8496；181214 53965；173021 04490

9020908Hinge, lid, SMC, QGXCNY

9020643Waste chute, straight, AS, Cabinet QsymCNY

9020632Kit, hinges (4), Cabinet QsymCNY

9020629Door, waste, SP, Cabinet QsymCNY

9020625Kit, repair, Cabinet QsymCNY

9020332EPROM - Motherboard, RGQCNY

9020233Foot assembly, rear, CASCNY

9020158Insulation disc - chamber bottom, RG3CNY

9020096Locking Pin, TLyser 2CNY

9020085Thrust Washer, TLyserCNY

9239498V-Housing, LX100CNY

9239490EX Laser Driver, UniphaseCNY

9239390PCR Plate Adapter, M96CNY

9236510BR 3000, PM ServiceThe Overhaul covers all travel ａnd labor costs plus all necessary parts to perform a Preventative Maintenance,. The instrument will also be thoroughly checked ａnd inspected to determine if any additional parts are required to get the instrument running to its optimal performance. There will be an additional charge for any such parts if any are needed.CNY

9232764Disposable Troughs, 20 / 30 ml (10)Troughs holding up to 20 ml of liquid; pack of 10CNY

9236472BR 9600, Full AgreementThe Full Agreement 9600 provides full service coverage for the BioRobot 9600. Costs for service visits are fully covered including travel, labor, ａnd parts. The agreement also includes one annual preventive maintenance visit, with costs for labor ａnd parts covered. With a Full Agreement, there is a priority response time of 48 hours (2 working days).CNY

9236443BR, InstallationThe Installation, BR Universal facilitates the quick implementation of the BioRobot into the lab routine by minimizing the instrument start-up phase. It covers the hardware ａnd software installation of the BioRobot Universal instrument ａnd provides the user with an introductory training on operation ａnd user maintenance. The installation includes labor ａnd travel costs. The performance of the installation process is documented on a GMP/GLP-compliant Field Service document.CNY

9239155Assembly, vertical axis, TWICNY

9239108Assy, Sample Needle, Actuator linkageCNY

9232693MTP-Plate Holder  2.01CNY

9232629Bottle, 500-ml, yellow fittingCNY

9232602Vacuum manifold, plate holder bottomlessCNY

9232579Cooling block, 1,5mlCNY

9238951Locking lever, BS15CNY

9238798Rectangular bucket, sealable with capCNY

9238794Angle rotor 6 x 250 mlCNY

9016913Tubing, press relief valve inlet DISU v2CNY

9238942Keyboard-Display assembly, BS15CNY

9238753Screwdriver, hex2mm, z-drive BR8CNY

9238916Power supply 40W, BS96CNY