9019499ReagBlock, 8x1.5ml/2ml/1.5ml Ta/Flat/TaCNY

9241225QIAcube, Inspection Service"The Annual Inspection Service, QIAcube is an on-site equipment service, performed by a QIAGEN service specialist. 

 

All required testing material ａnd certified equipment is provided by the service specialist. During the half day-long procedure, all application-critical modules of the QIAcube are inspected ａnd tested. Performed tests ａnd test results are documented in a Visit Report."CNY

9241218HC2, Full Agreement, no PM"Service response time (on-site repair):not applicable

Periodic inspection/maintenance: no, not included

Cost coverage depot repair (parts, labor, packaging, shipping): yes, full coverage

 

For defect DML, after customer calling QIAGEN technical service hotline before 12 am:

 

- A special package containing a replacement unit shall be sent to the customer within 2 working days.

- Customer shall send the defect unit to QIAGEN Regional Repair Center following the instructions attached with the packaging.   

 

For DML owned by customer, QIAGEN Regional Repair Center will send back the repaired original unit to customers within 7-10 working days.

 

PC, Monitor, Heater, Shaker, Washer, Printer ａnd Votexer:

- A new unit shall be sent to customer within  7-10 working days at no extra cost

- Customer shall send the defect unit to QIAGEN for disposal

- On-site installation of PC ａnd application software is not covered by the agreement"CNY

9241182Belt, Y, QXCNY

9238820Rect. carrier for 2 tubes 50 mlCNY

9233269Motor, X, BR8000CNY

9237165Power Supply XYPCNY

9233156Power Cord, USACNY

9237160Cover LiquiChipCNY

9237117Upgrade App., DyeEx 96CNY

9237115Upgrade App., Ni-NTA BeadsCNY

9237100Calibrate BR, on-siteCNY

9237091Training, BR On-site IntroductoryThe On-Site QIAGEN BioRobot Systems Introductory Training covers up to 16 hours of training time to refresh current users or introduce new users to the QIAGEN BioRobot Systems hardware ａnd QIAsoft Operating System software.  Participants are given an overview of the hardware system ａnd maintenance/troubleshooting procedures before exploring the three software environments of the QIAsoft Operating System.  Each software environment is explained in detail, ａnd users are taken step by step through each section with explanations on how to best adjust or write new protocols for their BioRobot System.  An introduction to teaching new ａnd exisiting slots ａnd racks is followed by writing a new protocol which uses these with the three available pipetting options, pooling, distributing ａnd transfer.  Users are encouraged to write protocols in the proper format creating prompts, flushes, ａnd correct pipetting parameters.  The training concludes asprotocols are tested ａnd run reinforcing concepts ａnd demonstrating success.CNY

9236407Storage Platform TW I, microplateCNY

9236364Sheath FilterCNY

9232933Microplate Reader(Agglutination)ModuleCNY

9232916Card, liquid detection 1.02CNY

9232910Board, Z1 motorCNY

9236351Tubing, Valve to injection needleCNY

9236326Sheath Pressure SensorCNY

9235760Seal, O-ring, 3mmCNY

9230926Motor Connecting Ground CableCNY

9230545Wanne fuer Abschirmung Plato 1xxxCNY

9235700Power Cable 24V, RCS1CNY

9230291Tubing Guide (periscope)CNY

211011QuantiTect Virus Kit (50)CNY

979017MOTT 16S Primer 2 For SequencingCNY

59824EpiTect Fast DNA Bisulfite Kit (50)CNY

206246Type-it Microsatellite PCR Kit (2000)CNY

9012742Syringe pump outlet tubing (4.7 m)CNY

9012736Peristaltic pump outlet tubing (1.0 m)CNY