产品展示
漏电起痕试验仪
点击次数:104发布时间:2020/4/3 13:44:47
更新日期:2020/4/3 13:44:47
所 在 地:
产品型号:LDQ - 2
优质供应
详细内容
LDQ-2漏电起痕试验仪
LDQ-2 leak testing instrument
功能特点
Functional characteristics
漏电起痕试验装置是按IEC60695、GB4207/IEC60112等标准要求设计制造的专用检测仪器。适用于固体绝缘材料在潮湿条件下相比漏电起痕指数和耐漏电起痕指数的测定,具有简便、准确、可靠、实用等特点。
The leak testing device is designed and manufactured according to IEC60695, GB4207/IEC60112 and other standards. Suitable for solid insulation materials in wet conditions compared to the leakage of the trace index and the resistance of the trace index of the determination, with a simple, accurate, reliable, practical and other characteristics.
设计标准:GB/T4207-2003固体绝缘材料在潮湿条件下相比电痕化指数和耐电痕化指数的测定方法
Design standard: GB/T4207-2003 solid insulating materials in wet conditions compared to the electrical trace of the index and the resistance of the measurement method of resistance
适用标准:IEC60695
Applicable standards: IEC60695
主要技术参数
Main technical parameters
1.电极材料 :试验电极 - 铂金,电极接杆 - 铜(铂金纯度达到标准要求99%)
The 1 electrode material: test electrode - platinum electrode rod - copper (Platinum purity standard 99%)
2.电极尺寸 :( 2mm ± 0.1mm )×( 5mm ± 0.1mm )×( 40mm ± 5mm )
2 electrode size: (2mm + 0.1mm) * (5mm + 0.1mm) * (40mm + 5mm)
3.铂电极 12mm ,30°±2°斜面
3 platinum electrode 12mm, 30 degrees - 2 degrees slope
4.电极距离:4.0mm ± 0.01mm ,夹角 60°±5°
The 4 electrode distance: 4.0mm + 0.01mm, angle 60 degrees - 5 degrees
5.电极压力:1.00N±0.01N
5 electrode pressure: 1.00N + 0.01N
6.试液电阻:A液 0.1%NH4Cl,3.95±0.05Ωm;B液 1.98±0.05Ωm
6 test of resistance: A liquid 0.1%NH4Cl 3.95 + 0.05, Omega m; B liquid 1.98 + 0.05 Omega M
7.滴液装置:试验时不需要调整,操作简单
7 drop device: the test does not need to adjust, the operation is simple
8.液滴高度:35mm ± 5mm ( 可调节 )
8 drop height: 35mm + 5mm (adjustable)
9.液滴时间 :30s±0.01s(优于标准)(数显,可预置调节 )
9 drop time: 30s + 0.01s (better than standard (digital), can be preset)
50滴时间 24.5min±2min
The 50 time 24.5min + 2min
10.液滴滴数 :1 ~ 9999( 数显,可预置 )
10 drop number: 1 ~ 9999 (digital display, preset)
11.试验风速 :0.2m /s( 新标准 )
11 test: 0.2m /s (wind new standard)
12.试验电压 :100V ~ 600V(25V 分度,可调节 )
12 test voltage: 100V ~ 600V (25V indexing, adjustable)
13.电源压降 :1.0A ± 0.1A 时 8%
13 power supply voltage drop: 1.0A + 0.1A when 8%
14.起痕判断 :0.50A ±10% , 2.00s±10%
14 marks: 0.50A judgment + 10% 2.00s + 10%.
15.施加电压在100~600V(48~60Hz)之间可调,短路电流在1.0±0.0001A(优于标准0.1A)时电压下降不超过10%;
15 applied voltage between 100 ~ 600V (48 ~ 60Hz) can be adjusted, short circuit current in 1 + 0.0001A (better than the standard 0.1A) when the voltage drop is not more than 10%;
16. 排气孔:?100mm
16 vent: O 100mm
17.空气环境:温度0~40℃ 相对湿度:≤80% 无明显振动及腐蚀性气体的场所
17: air temperature 0~40 relative humidity: less than 80% without obvious vibration and corrosive gas
18.当试验回路中,短路电流大于0.5A时间维持2秒钟继电器动作,切断电流,指示试品不合格;
18 when the test loop, the short circuit current is greater than 0.5A time to maintain 2 seconds relay action, cut off the current, indicating that the test is not qualified;
19.试验电源 :220V 0.6kVA 50-60Hz
19 test power: 220V 0.6kVA 50-60Hz
20.外型尺寸:宽1160mm×深600mm×高1295mm
20 exterior dimension: wide 1160mm * Deep 600mm * high 1295mm
21.燃烧试验区容积:0.5m3,宽900mm×深560mm×高1010mm, 背景黑色,背景照度≤20Lux
21 combustion zone volume: 0.5m3, width 900mm * 560mm * 1010mm deep high, black background, background illumination is less than or equal to 20Lux
使用范围
Range of use
测量在电压达600V时固体电气绝缘材料在电场作用下表面暴露于含杂质的水时的相对耐电痕化性能。当将电压施加到放在材料表面上规定 的电极装置之间,且电解液以规定的时间间隔滴到两电极之间时,在此试验情况下可能产生电痕化。引起材料破坏所必需的液滴数随着施加电压的减小而增加,且在低于某一限值时,不发生电痕化。当材料在试验电压下也未电痕时,可以有不同程度的腐蚀,且腐蚀深度能测出。某些材料能在试验时燃烧。
The relative resistance to electrical resistance of solid electrical insulating materials at voltages up to 600V at the time of the electric field under the action of an electric field is measured. When the voltage is applied between the electrodes placed on the surface of the material and the electrolyte is placed between the two electrodes at a prescribed time interval, an electrical scar may be produced. The number of droplets required to cause the destruction of the material is increased with the decrease of the applied voltage, and the electrical mark does not occur when the value is below a certain limit. When the material is under the maximum test voltage, it can have different degrees of corrosion, and the corrosion depth can be measured. Some materials can be burned in the test.
随货清单
List of goods
1 说明书 份 1
1 manual copy 1
2 燃烧箱 台 1
2 combustion chamber 1
3 排烟管 份 1
3 exhaust pipe 1
4 合格证 份 1
4 qualified certificate 1
5 不锈钢块规 个 1
A 1 gauge stainless steel 5
6 玻璃方块 块 1
6 glass block 1
7 试验针头 个 1
7 test needle 1
8 保险丝 个 1
8 fuse 1
9 电源线 根 1
9 power cord 1
相关设备:
ZLD-6000V高压漏电起痕试验仪
ZJC-100KV电压击穿试验仪
ZST-121体积表面电阻率测试仪