![logo](/images/logo_05.png)
您的位置:首页 > 产品展厅 > 化工原料 > 化学试剂 > 生化试剂 > 大鼠白介素4(IL-4)ELISA试剂盒厂家
齐一生物试剂盒组分经过重重优化,每个组分的稳定性都完美的经过高温破坏测验,最大程度的避免了长途运输和保存过程中抗原抗体的失活.齐一生物试剂盒凭借其完美的标曲.严格的质控.稳定高、易保存,操作简便,已广泛应用在全国免疫学检验研究所的各领域中.深受研究者们的青睐. 齐一生物销售:021-6034 8496;181214 53965;173021 04490
【大鼠白介素4(IL-4)ELISA试剂盒厂家】齐一生物试剂盒凭借其完美的标曲、严格的质控、较高的稳定性,在世界范围内的科研试剂领域中脱颖而出深受研究者们的青睐. 齐一生物销售:021-6034 8496;181214 53965;173021 04490
【友情提示】:本产品仅供科研研究使用,不得用于人体临床直接检测。避免给您带来不必要的损失,请仔细阅读购买说明!
试验所需自备物品:
1. 酶标仪(450nm 波长滤光片)
2. 高精度移液器,EP 管及一次性吸头
3. 37℃恒温箱,双蒸水或去离子水
4. 吸水纸
【大鼠白介素4(IL-4)ELISA试剂盒厂家】试剂盒安全性提示:
1.工作人员实验中避免直接接触终止液和底物A、B。一旦接触到这些液体,请尽快用水冲洗。
2.实验中不要吃喝、抽烟或使用化妆品。
3.不要用嘴吸取试剂盒里的任何成份。
操作注意事项:
1.试剂盒应按标签说明书储存,使用前恢复到室温30分钟后方可使用。稀稀过后的标准品应丢弃,不可保存。
2.实验中不用的板条应立即放回包装袋中,密封保存,以免变质。
3.不用的其它试剂应包装好或盖好。不同批号的试剂不要混用.请在试剂盒保质前使用。
4.使用一次性的吸头以免交叉污染,吸取终止液和底物A、B液时,避免使用带金属部分的加样器。
5.使用干净的塑料容器配置洗涤液。使用前充分混匀试剂盒里的各种成份及样品。
6.洗涤酶标板时应充分拍干,不要将吸水纸直接放入酶标反应孔中吸水。
7.底物A应挥发,避免长时间打开盖子。底物B对光敏感,避免长时间暴露于光下。避免用手接触,有毒。实验完成后应立即读取OD值。
8.加入试剂的顺序应一致,以保证所有反应板孔温育的时间一样。
9.按照说明书中标明的时间、加液的量及顺序进行温育操作。
【大鼠白介素4(IL-4)ELISA试剂盒厂家】齐一生物供应ELISA试剂盒检测的目的是为实验提供准确可靠的定量分析实验依据。为了保证实验数据的可靠性,在实验过程中必须坚持全面质量控制和全过程质量控制。在收集标本前都必须有一个完整的计划。
操作步骤
实验开始前,请提前配置好所有试剂,试剂或样品稀释时,均需混匀,混匀时尽量避免起泡。每次检测都应该做标准曲线。如样品浓度过高时,用样品稀释液进行稀释,以使样品符合试剂盒的检测范围。
1. 加样:分别设空白孔、标准孔、待测样品孔。空白孔加样品稀释液100μl,余孔分别加标准品或待测样品100μl,注意不要有气泡,加样将样品加于酶标板孔底部,尽量不触及孔壁,轻轻晃动混匀,酶标板加上盖或覆膜,37℃反应120分钟。
为保证实验结果有效性,每次实验请使用新的标准品溶液。
2. 弃去液体,甩干,不用洗涤。每孔加生物素标记抗体工作液 100μl(取1μl生物素标记抗体加99μl生物素标记抗体稀释液的比例配制,轻轻混匀,在使用前一小时内配制),37℃,60分钟。
3. 温育60分钟后,弃去孔内液体,甩干,洗板3次,每次浸泡1-2分钟,350μl/每孔,甩干。
4. 每孔加辣根过氧化物酶标记亲和素工作液(同生物素标记抗体工作液) 100μl,37℃,60分钟。
5. 温育60分钟后,弃去孔内液体,甩干,洗板5次,每次浸泡1-2分钟,350μl/每孔,甩干。
6. 依序每孔加底物溶液90μl,37℃避光显色(30分钟内,此时肉眼可见标准品的前3-4孔有明显的梯度蓝色,后3-4孔梯度不明显,即可终止)。
7. 依序每孔加终止溶液50μl,终止反应(此时蓝色立转黄色)。终止液的加入顺序应尽量与底物液的加入顺序相同。为了保证实验结果的准确性,底物反应时间到后应尽快加入终止液。
8. 用酶联仪在450nm波长依序测量各孔的光密度(OD值)。 在加终止液后15分钟以内进行检测。
【大鼠白介素4(IL-4)ELISA试剂盒厂家】注:
1. 用户在初次使用试剂盒时,应将各种试剂管离心数分钟,以便试剂集中到管底。
2. 每次实验留一孔作为空白调零孔,该孔不加任何试剂,只是最后加底物溶液及2N H2SO4。测量时先用此孔调OD值至零。
3. 为防止样品蒸发,试验时将反应板放于铺有湿布的密闭盒内,酶标板加上盖或覆膜。
4. 未使用完的酶标板或者试剂,请于2-8℃保存。标准品、生物素标记抗体工作液、辣根过氧化物酶标记亲和素工作液请依据所需的量配置使用。请勿重复使用已稀释过的标准品、生物素标记抗体工作液或、辣根过氧化物酶标记亲和素工作液。
5. 建议检测样品时均设双孔测定,以保证检测结果的准确性。
以上资料仅供您参考,如有问题欢迎来电,齐一生物销售:021-6034 8496;181214 53965;173021 04490
9240630 Power Supply, 5VDC 1.5 AMP, AP96 CNY
9240593 Unload Valve, Pump, Pressure, AP196/98 CNY
9240562 Fuse, PCB, 315, Eppendorf, AP196/98 CNY
9240536 Motor Assy, SiNug, 17, All, AP96/196 CNY
9240514 CD R/W, AP196/98 CNY
9240504 PC-104, AP98 CNY
9240346 Autopure, Full Agreement "Repair service delivery: onsite
Service response time (repair): 48 hours/2 business days
Periodic inspection/maintenance: yes, 1/agreement year
Inspection/maintenance delivery: onsite
Cost coverage for repair parts: yes, included
Cost coverage for labor: yes, included
Cost coverage for travel: yes, included
Replacement system (Loaner) provision: not included
Transportation cost coverage: not applicable" CNY
9240098 Re-Installation, BR EZ1 The Re-Installation, BR EZ1 facilitates quick implementation of system back into lab routine by minimizing instrument set-up phase. It covers hardware and software check of instrument and provides user with operator refesher overview. Re-installation includes labor and travel costs. Re-installation performance process is documented on a GMP/GLP-compliant Field Service document. CNY
9239852 Foot bumpers, v2.0 (4) CNY
9019944 Cable, P-axis, wires, 8 ch. , C18 CNY
9238880 Bearings up. & low, BS96 CNY
9238836 BioSprint96, Basic Agreement, no PM "Repair service delivery: onsite
Service response time (repair): 5 business days
Periodic inspection/maintenance: not included
Inspection/maintenance delivery: not applicable
Cost coverage for Repair Parts : yes, full coverage
Cost coverage for labor: yes, full coverage
Cost coverage for travel: yes, full coverage
Replacement system (Loaner) provision: not applicable
Transportation cost coverage: not applicable" CNY
9241211 Full Agreement Depot Repair, DML2000, 1y "The Full Agreement Depot Repair, DML2000 provides full service coverage for the DML 2000 luminometer. The service is conducted as an instrument exchange service.
All shipping, labor and repair part costs related to an instrument exchange are included for 1 year. Instrument exchange time is 2 - 3 working days." CNY
9241191 Magnet, tool, QX CNY 【大鼠白介素4(IL-4)ELISA试剂盒厂家】
9238825 Spare bucket for plate rotor CNY
9238815 Rect. carrier for 12 tubes 10 ml w/ cap CNY
9019472 TAPE SPACER CLEAR GS CNY
9019464 UV tube, Cxx CNY
9243650 Comprehen Valid., EZ1/QIAcube/QIAsymph """The Comprehensive Validation Support plan specific to a laboratory's needs will incorporate all of the requirements for the internal validation guidelines from the FBI's Quality Assurance Standards (QAS).
The Comprehensive Validation Support service includes all travel and labor charges for up to 20 days by the QIAGEN Validation Team. Typically, one week will be required to extract, quantify, and amplify the validation study samples and may require multiple individuals. Usually, two weeks is required to analyze the data and one week to write the final report. The expected time period to complete the Comprehensive Validation is six weeks. The actual time may vary depending on resource availability, including laboratory time dedicated to validation activities.
Lab Work – The QIAGEN specialist(s) will travel to the laboratory to conduct the on-site validation lab work. The QIAGEN specialist team will perform and complete all extractions, quantifications, amplfications, and capillary electrophoresis. The laboratory is responsible for providing systems/protocols that may be needed (generally laboratory SOPs, ex. interpretation guidelines). Additionally, the laboratory staff may be required to provide additional data needed for interpretation (ex. quantification/amplification/CE results) during the data review phase of the validation.
Once the final scope of the validation is determined, QIAGEN will provide a quote for all consumables required for the validation. Non-QIAGEN chemistry and accessories are not included and should be purchased to cover the validation experimental design including qPCR, STR, NIST standards, required samples types (blood, semen, buccal samples) and required substrates (swabs, materials, etc). The Customer is expected to have all materials on-hand 1 week prior to the validation start date.
Data Analysis – The Comprehensive Validation Support plan encompasses data collection (quants, amps, CE) during the on-site visit. The laboratory may be responsible for sharing (typically electronically via e-mail) any validation data requested after the on-site visit. A QIAGEN specialist will complete all of the data analysis produced from the validation study design. This includes qPCR (quant) and STR (amp) analysis and linkage to starting samples.
Validation data CD/flashdrive – QIAGEN will review the validation data and draft a validation summary document, ensuring compliance with the FBI's QAS requirements/standards. QIAGEN will send validation data in an electronic format (email/CD/flashdrive) to the laboratory. The laboratory is responsible for final compilation, any format change preferences, review and signoff of the validation report. The documentation provided by QIAGEN will aide in demonstrating compliance with all accreditation guidelines during laboratory audits. Should a hard copy of the validation study be preferred, the laboratory is required to specify prior to the onset of the validation.
Post-validation QIAGEN-to-Laboratory Transfer – Following completion of the validation and generation of the draft validation summary document, a designated member of the QIAGEN validation team will review the validation with the Lab Manager and the Technical Leader. Following sign off on the validation report, training of the laboratory DNA staff will occur. Refer to the Post-validation Competency Training for additional information. """ CNY
9237333 Install, BR plus 3 integr. w. scheduling Installation and training, BioRobot System including three approved integration devices with scheduling CNY
9237328 Upgrade, BR & 2 ext. devices w. sched. Upgrade BioRobot with two approved integration devices using scheduling software CNY
9237173 Shield, V-housing CNY
9233208 Tubing, liquid system 2.5/1.5 CNY
9237155 V-Housing with Sample Needle CNY
9237150 Heater Top CNY
9016151 #App. Package, M48, Pathology CNY
9019179 Opto - plate lock closed, PyroQ96MD CNY
9011883 Upgrade, high speed pipetting system CNY
9011882 Back unit, BR9600 CNY
9011823 Z-Modul; Tip-Adapter 300µl; BR8000 CNY 【大鼠白介素4(IL-4)ELISA试剂盒厂家】
9236916 3 Year Warranty, LiquiChip LiquiChip 3-year Warranty with 1 Preventive Maintenance per year. Included in system price. This warranty must be included as a line item on the system quote. It covers the system for three years total including all per incident travel and labor charges, all repair parts, one preventive maintenance visits per year (three in total), and 48- hour priority response. CNY
QY-x1169 人乳腺癌高转移细胞MDA-MB-435
QY-x1170 人乳腺癌细胞MDA-MB-435S
QY-x1171 人乳腺癌细胞MDA-MB-436
QY-x1172 人乳腺导管癌细胞MDA-MB-453
QY-x1173 人乳腺细胞HBL-100
QY-x1174 人乳腺癌细胞BCaP-37
QY-x1175 人乳腺癌细胞LCC1
QY-x1176 人乳腺癌细胞MX-1
QY-x1177 人乳腺管癌细胞T47D
QY-x1178 人乳腺癌细胞SK-BR-3 【大鼠白介素4(IL-4)ELISA试剂盒厂家】
QY-x1179 人乳腺癌细胞4T1
QY-x1180 人乳腺癌细胞HCC1937
QY-x1181 人乳腺导管癌细胞HCC38
QY-x1182 人乳腺癌细胞Hs-578T
QY-x1183 人乳腺癌Tamoxifen耐药株LCC2
QY-x1184 人乳腺癌抗雌激素耐药株LCC9
QY-x1185 人乳腺癌阿霉素耐药细胞株MCF/Adr
QY-x1186 人乳腺癌细胞BT-549
QY-x1187 人乳腺导管瘤细胞BT-474
QY-x1188 人乳腺癌细胞MB-271
QY-x1189 人乳腺癌细胞ER-30
QY-x1190 人乳腺癌细胞M453
QY-x1191 人乳腺浸润性导管癌旁皮肤细胞CCD-1095Sk
QY-x1192 人乳腺细胞HBL-100
QY-x1193 人乳腺导管瘤细胞UACC812
QY-x1194 人乳腺癌细胞系1590 【大鼠白介素4(IL-4)ELISA试剂盒厂家】
QY-x1195 人卵巢癌细胞A2780
QY-x1196 人卵巢癌细胞Sw626
QY-x1197 人卵巢癌顺铂耐药株COC1/CDDP
QY-x1198 人卵巢癌紫杉醇耐药株A2780/Taxol
QY-x1199 人卵巢癌细胞系Anglne
QY-x1200 人卵巢癌细胞OVCaR-3
QY-x1201 人卵巢癌细胞Caov-3
大鼠转铁蛋白(TRF)ELISA试剂盒厂家 QY-R2810 国产/进口原装 48T/96T 齐一生物科技(上海)有限公司销售:021-6034 8496;181214
大鼠3-羟-3-甲戊二酸单酰辅酶A还原酶(HMG-CoAR)ELISA试剂盒现货
大鼠3-羟-3-甲戊二酸单酰辅酶A还原酶(HMG-CoAR)ELISA试剂盒现货 QY-R2809 国产/进口原装 48T/96T 齐一生物科技(上海)有限公司销售:021-6034&
大鼠脂多糖/内毒素(LPS)ELISA试剂盒厂家 QY-R2808 国产/进口原装 48T/96T 齐一生物科技(上海)有限公司销售:021-6034 8496;181214
① 凡本网注明"来源:易推广"的所有作品,版权均属于易推广,未经本网授权不得转载、摘编或利用其它方式使用。已获本网授权的作品,应在授权范围内
使用,并注明"来源:易推广"。违者本网将追究相关法律责任。② 本网凡注明"来源:xxx(非本网)"的作品,均转载自其它媒体,转载目的在于传递更多信息,并不代表本网赞同其观点和对其真实性负责,且不承担此 类作品侵权行为的直接责任及连带责任。如其他媒体、网站或个人从本网下载使用 ,必须保留本网注明的"稿件来源",并自负版权等法律责任。
③ 如涉及作品内容、版权等问题,请在作品发表之日起两周内与本网联系,否则视为放弃相关权利。
④易推广页面显示产品信息均由企业自主发布,信息内容真实性、准确性与合法性由相关企业负责,易推广对此不承担任何责任,如遇非法或侵权信息欢迎监督,请联系QQ:1273397930或者发邮件至:1273397930@qq.com,如有确实证件证明属实,本站将对其删除处理,谢谢!
⑤ 本信息由注册会员:齐一生物科技(上海)有限公司发布并且负责版权等法律责任。
易推广客服微信