当前位置： 易推广 > 智能控制 > 电源 > 整流器 > 山东格伦德电源科技有限公司 > 产品展示 > 48v开关电源模块 > 动力源DZY-48/50D1整流模块48V50A 动力源DZY-48/50D1
动力源DZY-48/50D1整流模块48V50A 动力源DZY-48/50D1
价格：￥电议
品牌名称：$brandModel.Title(进口品牌)型号： 原产地：中国大陆 发布时间：2020/1/3 17:36:57更新时间：2024/10/28 11:59:17
产品摘要：DZY-48/50D1 动力源48V50A整流模块 DZY-48/50D1动力源DUM-48/50B型智能开关电源机柜上的整流模块 DZY-48/50D1
产品完善度： 访问次数：372
企业档案
会员类型：初级版会员
已获得易推广信誉 等级评定
16成长值
(0 -40)基础信誉积累，可浏览访问
(41-90)良好信誉积累，可接洽商谈
(91+ )优质信誉积累，可持续信赖
易推广初级版会员：7年
工商认证 【已认证】
最后认证时间：
注册号： 【已认证】
法人代表： 【已认证】
企业类型：经销商 【已认证】
注册资金：人民币万 【已认证】
产品数：244
参观次数：809755
手机网站：http://m.yituig.com/c133773/
商铺地址：http://
详细内容
DZY-48/50D1 动力源48V50A整流模块 DZY-48/50D1
DZY-48/50D1 动力源48V50A整流模块 DZY-48/50D1
动力源DUM-48/50B型智能开关电源机柜上的整流模块 DZY-48/50D1 功能： 将交流AC220V转换成直流DC48V输出； 显示整流器输出电压、电流、内部温度等状态； 能够实现多机并联输出； 通过RS485与系统控制器实现通讯。
整流器的可靠性设计:
安装整流器 整流模块安装时，将整流模块前面板的定位销向上提起，将整流模块缓慢推入整流模块的安装位置 。
由于整流模块的输出电路的后级是滤波电路，有较大的电容，在线测量时，万用表的内部电池会为电容充电，万用表的测量值会逐渐上升，这是正常现象，不要误以为短路。
拆除整流模块 断开被更换的整流模块交流控制开关； 拉开整流模块的拉手，模块固定销收起，将模块拔出。 安装整流模块 整流模块的安装，分两次推入电源机柜; 首先，将整流模块放入机柜，不要拉开模块拉手，缓慢将模块推入机柜，模块固定销卡到限位槽后停止； 等到3秒钟后，来开模块拉手，固定销收起，再次将整流模块完全推入机柜， 放开模块拉手，固定销落下，模块被固定； 闭合整流模块的交流控制开关，模块启动。 一、整流器告警处理
显示板应显示’…’状态延时数秒开机。绿灯亮表示整流器正常，红灯亮表示整流器故障。上电面板按键按下显示模块电流，面板按键弹起依次显示模块温度、ID号、模块电压，显示电流时,绿灯和电流指示灯同亮; 显示温度时, 灯都不亮; 显示ID号时,只有绿灯亮; 显示电压时,绿灯和电压指示灯亮; 若黄灯亮则ID号对应显示为: E11 输入欠压 E12 输入缺相 E13 输出欠压 E14 风机故障 E15 温度>70度 ID 通讯故障(如模块单机调试时未接通讯,此故障可不必理会); 若红灯亮则ID号对应显示为: E01 输入过压 E02 输出过压 E03 保险 E04 模块故障 E05 温度>90度
整流器绝缘耐压3000V，防止雷电浪涌破坏 主要特点:
1、效率高 功率管工作在开关状态； 关断时没有功耗，导通时功耗小 2、体积小，重量轻 因为变压器的圈数、滤波电容的容量均与频率成反比，高频开关电源频率高，也就是说变压器的圈数和滤波电容的容量小，所以高频开关电源体积小，重量轻。
整流器的设计:
PFC有源功率因数校正设计： 选用控制芯片TDA16888 1、驱动波形为修正波形。 2、PFC和PWM工作同步，可减少电流冲击，元件使用寿命高。 变压器的设计： 三重防护导线绕制
DZY-48/50D1 Power Source 48V50A Rectifier Module DZY-48/50D1
DZY-48/50D1 Power Source 48V50A Rectifier Module DZY-48/50D1
Rectifier Module DZY-48/50D1 on Power Source DUM-48/50B Intelligent Switching Power Supply Cabinet
Functions: AC AC220V is converted into DC DC48V output; the output voltage, current ａnd internal temperature of rectifier are displayed; multi-machine parallel output is realized; communication with system controller is realized by RS485.
Reliability design of rectifier:
When the rectifier module is installed, the positioning pin of the front panel of the rectifier module is lifted upward, ａnd the rectifier module is pushed slowly into the installation position of the rectifier module.
Because the output circuit of the rectifier module is a filter circuit ａnd has large capacitance, when measuring online, the inner battery of the multimeter will charge the capacitance, ａnd the measurement value of the multimeter will gradually rise. This is a normal phenomenon. Don＇t mistake short circuit for it.
Remove the rectifier module, disconnect the AC control switch of the replaced rectifier module, pull the handle of the rectifier module, retract the fixed pin of the module ａnd pull the module out. Firstly, put the rectifier module into the cabinet, don＇t pull the module handle, push the module into the cabinet slowly, ａnd stop after the module fixed pin card reaches the limit slot; Wait until 3 seconds, open the module handle, put the fixed pin back, push the rectifier module into the cabinet completely again, ａnd release the mould. Block handle, fixed pin falling, module fixed; Close the AC control switch of rectifier module, module start. I. Warning Processing of Rectifier
The display panel should display＇...＇ The state delay is several seconds. The green light indicates that the rectifier is normal, ａnd the red light indicates that the rectifier is faulty. The power-on panel button presses the display module current, ａnd the panel button pops up to display module temperature, ID number ａnd module voltage in turn. When displaying current, the green light ａnd current indicator light are on the same light; when displaying temperature, the light is not on; when displaying ID number, only the green light is on; when displaying voltage, the green light ａnd voltage indicator light are on; if the yellow light is on, the ID number corresponds to: E11 input under-voltage; * E12 Input phase absence, Output undervoltage, E14 fan failure, E15 temperature > 70 degree ID communication failure (if the module is not connected during single debugging, this failure is not ignored); if the red light is on, ID number corresponds to: E01 input overvoltage, E02 output overvoltage, E03 guarantee Risk E04 module failure E05 temperature > 90 degrees
Rectifier insulation withstands 3000V to prevent lightning surge damage
Main features:
1. High efficiency power transistor works in the switching state; there is no power consumption when switching off, the power consumption when turning on is small 2, the volume is small, ａnd the weight is light. Because the number of transformer turns ａnd the capacity of filter capacitor are inversely proportional to the frequency, the frequency of high frequency switching power supply is high, that is to say, the number of transformer turns ａnd the capacity of filter capacitor are small, so the high frequency switching power supply is small in volume ａnd light in weight.
Rectifier design:
PFC active power factor correction design: control chip TDA16888 1 ａnd drive waveform are selected as correction waveform. 2. PFC ａnd PWM work synchronously, which can reduce the current impact ａnd improve the service life of components. Transformer design: triple protective wire winding
DZY-48/50D1 动力源48V50A整流模块 DZY-48/50D1
DZY-48/50D1 动力源48V50A整流模块 DZY-48/50D1
DZY-48/50D1 动力源48V50A整流模块 DZY-48/50D1
动力源DUM-48/50B型智能开关电源机柜上的整流模块 DZY-48/50D1
整流器的可靠性设计:
由于整流模块的输出电路的后级是滤波电路，有较大的电容，在线测量时，万用表的内部电池会为电容充电，万用表的测量值会逐渐上升，这是正常现象，不要误以为短路。
拆除整流模块 断开被更换的整流模块交流控制开关； 拉开整流模块的拉手，模块固定销收起，将模块拔出。 安装整流模块 整流模块的安装，分两次推入电源机柜; 首先，将整流模块放入机柜，不要拉开模块拉手，缓慢将模块推入机柜，模块固定销卡到限位槽后停止； 等到3秒钟后，来开模块拉手，固定销收起，再次将整流模块完全推入机柜， 放开模块拉手，固定销落下，模块被固定； 闭合整流模块的交流控制开关，模块启动。
显示板应显示’…’状态延时数秒开机。绿灯亮表示整流器正常，红灯亮表示整流器故障。上电面板按键按下显示模块电流，面板按键弹起依次显示模块温度、ID号、模块电压，显示电流时,绿灯和电流指示灯同亮; 显示温度时, 灯都不亮; 显示ID号时,只有绿灯亮; 显示电压时,绿灯和电压指示灯亮; 若黄灯亮则ID号对应显示为: E11 输入欠压 E12 输入缺相 E13 输出欠压 E14 风机故障 E15 温度>70度 ID 通讯故障(如模块单机调试时未接通讯,此故障可不必理会); 若红灯亮则ID号对应显示为: E01 输入过压 E02 输出过压 E03 保险 E04 模块故障 E05 温度>90度
整流器绝缘耐压3000V，防止雷电浪涌破坏
1、效率高 功率管工作在开关状态； 关断时没有功耗，导通时功耗小 2、体积小，重量轻 因为变压器的圈数、滤波电容的容量均与频率成反比，高频开关电源频率高，也就是说变压器的圈数和滤波电容的容量小，所以高频开关电源体积小，重量轻。
整流器的设计:
PFC有源功率因数校正设计： 选用控制芯片TDA16888 1、驱动波形为修正波形。 2、PFC和PWM工作同步，可减少电流冲击，元件使用寿命高。 变压器的设计： 三重防护导线绕制
DZY-48/50D1 Power Source 48V50A Rectifier Module DZY-48/50D1
DZY-48/50D1 Power Source 48V50A Rectifier Module DZY-48/50D1
Rectifier Module DZY-48/50D1 on Power Source DUM-48/50B Intelligent Switching Power Supply Cabinet
Functions: AC AC220V is converted into DC DC48V output; the output voltage, current ａnd internal temperature of rectifier are displayed; multi-machine parallel output is realized; communication with system controller is realized by RS485.
Reliability design of rectifier:
When the rectifier module is installed, the positioning pin of the front panel of the rectifier module is lifted upward, ａnd the rectifier module is pushed slowly into the installation position of the rectifier module.
Because the output circuit of the rectifier module is a filter circuit ａnd has large capacitance, when measuring online, the inner battery of the multimeter will charge the capacitance, ａnd the measurement value of the multimeter will gradually rise. This is a normal phenomenon. Don＇t mistake short circuit for it.
Remove the rectifier module, disconnect the AC control switch of the replaced rectifier module, pull the handle of the rectifier module, retract the fixed pin of the module ａnd pull the module out. Firstly, put the rectifier module into the cabinet, don＇t pull the module handle, push the module into the cabinet slowly, ａnd stop after the module fixed pin card reaches the limit slot; Wait until 3 seconds, open the module handle, put the fixed pin back, push the rectifier module into the cabinet completely again, ａnd release the mould. Block handle, fixed pin falling, module fixed; Close the AC control switch of rectifier module, module start.
The display panel should display＇...＇ The state delay is several seconds. The green light indicates that the rectifier is normal, ａnd the red light indicates that the rectifier is faulty. The power-on panel button presses the display module current, ａnd the panel button pops up to display module temperature, ID number ａnd module voltage in turn. When displaying current, the green light ａnd current indicator light are on the same light; when displaying temperature, the light is not on; when displaying ID number, only the green light is on; when displaying voltage, the green light ａnd voltage indicator light are on; if the yellow light is on, the ID number corresponds to: E11 input under-voltage; * E12 Input phase absence, Output undervoltage, E14 fan failure, E15 temperature > 70 degree ID communication failure (if the module is not connected during single debugging, this failure is not ignored); if the red light is on, ID number corresponds to: E01 input overvoltage, E02 output overvoltage, E03 guarantee Risk E04 module failure E05 temperature > 90 degrees
Rectifier insulation withstands 3000V to prevent lightning surge damage
Main features:
1. High efficiency power transistor works in the switching state; there is no power consumption when switching off, the power consumption when turning on is small 2, the volume is small, ａnd the weight is light. Because the number of transformer turns ａnd the capacity of filter capacitor are inversely proportional to the frequency, the frequency of high frequency switching power supply is high, that is to say, the number of transformer turns ａnd the capacity of filter capacitor are small, so the high frequency switching power supply is small in volume ａnd light in weight.
Rectifier design:
PFC active power factor correction design: control chip TDA16888 1 ａnd drive waveform are selected as correction waveform. 2. PFC ａnd PWM work synchronously, which can reduce the current impact ａnd improve the service life of components. Transformer design: triple protective wire winding
DZY-48/50D1 动力源48V50A整流模块 DZY-48/50D1
DZY-48/50D1 动力源48V50A整流模块 DZY-48/50D1
热门标签：DZY-48/50D1 动力源整流模块
